log splitter valve sticking

Place the log splitter back upright and try the splitter again if it produces the same noise then loosen the bolts a little from the end of the pump 13mm and try again. Also it is hard to trip the lever to get it to stop retracting.

Log Splitter Valve 20 Gpm 1 2 Work Ports Auto Return Detent

1 Find the diagram.

. There will be input valves for the pressurized and un-pressurized hose connections and the diagram will show you which ones go on which side of the detent valve and in what order. Another reason for a slowed-down log splitter is a jammed motor due to blockage in the fan. I just bought a sweet 22-ton Splitter at Tractor Supply the Husky model made by Speeco I believe.

There are two common types of mounts used on log-splitters. If fluid is leaking from your pump disassemble it and replace all seals. This valve is the most prevalent valve used in the residential log splitter industry.

Log Splitters For Sale in Washington DC. Its a Huskee 22 ton and the valve is sticking both ways. If the hydraulic hoses are hooked up incorrectly then the valve wont be able to function properly.

My new to me Countyline Speeco 25 ton splitter control valve detent mechanism was sticking operating erratically and adjusting didnt solve the problem. The hydraulic directional valve controls the motion of the cylinder. And it simultaneously allows oil from the rod-end port of the cylinder to flow into.

If still your log splitter shuts off under load most likely your hydraulic pump is jammed or stuck in its high flowlow-pressure stage described as the first stage. The ball like a ball bearing moves in and out if you push on it and the. To fix this the bleed valve needs to be opened and the pressure plate needs to be cycled back and forth a few times.

There is a four-bolt mount and a two-bolt mount. If the oil is found to be enough then the problem is due to the air mixed with liquid when opening the bleed valve and cycling pressure plate. The two-bolt mount pumps come in 22gpm and 28gpm sizes and have a 58 keyed shaft that can differ in length.

Anyone ever rebuild a log splitter hydaulic valve. Remove the carriage from the log splitter. I have an old home made log splitter30 years never a lick of problemsIt has been sitting a couple of years it started like usualI worked it about 12 hour added about 1-12 quart of hydraulic fluid Sams Club AW 46 RO Hydraulic Oil finished my workThe next day I discovered the control flow valve was stuck and cannot move it also the pump is seized.

An automatic process is carried out for transition from the first stage to the second. I pulled the cap and found it contaminated with moisture and it was lubricated with a silver pastegrease. Blockage in the Fan.

And now it started to stick going out and it will go out to the end and stall. These vibrations or shaking could be due to the log splitter being low in hydraulic oil. Good morning I have an log splitter that my grandfather built over 25 years ago and has worked perfectly until this summer.

If the ram still does not return then contact the dealer on 0191 276 6553. Log Splitter Valve 20 Gpm 1 2 Work Ports Auto Return Detent Check the position of the lever. The next step is to replace the hydraulic oil seals as worn seals will allow oil to leak out of the system.

It all of a sudden stopped going into the two stage stronger pressure. The spool shifted by the handle has 3 positions. Check the manual to be sure you have proper lever position.

East Brady PA. An oil leak or air in the system will cause a loss in this driving force resulting in the plates slow movement. If you discover an oil leak in your hydraulic log splitter first check that the bleed valve is properly tightened.

When it retracts it pulls in tight and stalls the engine. The detent cover on the hydraulic valve controls the auto-return. I had the cylinder rebuilt by a machine shop first and no difference.

A hydraulic log splitter uses a hydraulic piston to get the driving force. Pushed one way it shunts oil from the pump to the base port of the cylinder causing it to extend. Remove the fan cover and try to turn it to see if it moves without difficulty.

Its a Huskee 22 ton and the valve is sticking both ways. The four-bolt mount pumps generally come in 5gpm-16 gpm sizes and have a ½ keyed shaft about 1-12 long. When the pump fails it will often send metal debris.

Find the diagram of the detent valve set up. Loosen the two rear lock nuts on the carriage arms and remove the two nuts in front of the crosspiece. This tutorial apply to the Energy control valve.

If the levels look correct when checking this could mean that there is air within the oil lines. Make sure the oil levels are correct and. If not then look for blockages in the fan and remove them.

It happens due to either the lower level of fluid or the air present in the system. Open the bleed valve first check the hydraulic oil level refill it if needed and then store your splitter in a shelter or garage. If the ram does not return after removing the DuoCut blade.

The seals on these pumps wear over time and eventually can cause hydraulic fluid to leak out of the system. When repairing a damaged pump it is important to carefully analyze and address the rest of the hydraulic system. The hydraulic cylinder was also starting to leak heavily.

Remove the air from the system to solve this problem and keep the bleed. A properly functioning hydraulic log splitter makes relatively easy work of splitting logs. In this stage the pump produces about 400-900psi which is far less than its rated GPM.

Works great but the actuation lever sticks in the up position so tightly that it rarely kicks back to neutral when the ram is all the way up and I end up leaping back to the splitter over log sections to manually flip it before the engine stalls or a hydralic hose blows. You need to check the amount of oil first. First turn the log splitter over and close off the air vent remove the motor and pump 3 x 13mm headed bolts and 1 x support bolt.

In the second stage or low flowhigh-pressure stage the pump produces 25 or less of its rated GPM but it does it at a higher. You can check for this issue easily. I have a Brave Log splitter and the last few weeks the detentspoil valve has become sticky after the I split a couple of hours.

Is this normal operation having a valve stick in on direction. Common problems with AL-KO and similar Chinese generic log splitters the hydraulic valve spindle breaks on the end stopping the unit from working correctly. What would you recommend.

The Hydraulic Log Splitter Valve. On one side of the valve there is a inch long bolt only way I know how to describe it with a ball in the end. Log Splitter Valve And Accessories By Energy Manufacturing Company Inc If a log is not splitting all the way through then the log may be too green or too large meaning that it would require a greater force than your log.

Having a two stage. Fixing the auto-return on a hydraulic control valve usually is just a matter of tightening The bolt inside the detent cover assembly.

25 Fix Log Splitter Hydraulic Control Valve O Ring Rebuild Youtube

2 Spool 25 Gpm Prince Log Splitter Lifter Valve Rd522ccea5a4b1 Directional Control Valves Hydraulic Valves Hydraulics Www Surpluscenter Com

Powermate 5 Tons 20 Amp Corded Electric Kinetic Power Log Splitter Walmart Com

Log Splitter Hydraulics And How It Works Cylinder Services Inc

Troy Bilt Mtd 27 Ton Splitter Valve Repair Youtube

Performance Built 27 Ton 208 Cu Cm Horizontal And Vertical Gas Log Splitter With Briggs Stratton Engine In The Hydraulic Gas Log Splitters Department At Lowes Com